Mircom FA-300 Series Manuel d'installation Page 59
- Page / 84
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
FA-300 Series LCD Version Installation and Operation Manual
51
8. i
3
Loop Test (Command-Menu)
The i
3
maintenance test is designed to test the devices on the i
3
zone. If there is noise on the line or if the device is
too far away from the panel, the devices may not respond to the panel inquiries. An i
3
maintenance test can be
invoked from the command menu. If the fire alarm has just been powered up or reset, wait six minutes before
selecting the i
3
loop test. If the i
3
loop test is selected, the following message appears on the screen:
If you select “yes” by pressing “ENTER”, the display will ask you for which zone you want to perform the i
3
test. Note
that only one zone at a time can be in maintenance test. Select the zone by pressing the “UP” and “DOWN” keys
and then pressing the “RIGHT” key to select the device. After the device is selected press “ENTER”.
If the i
3
maintenance test is selected within six minutes after power-up or reset, the following information message
is displayed.
If a zone is selected that is not configured as an i
3
zone, the following message is displayed:
Once the zone goes into the i
3
loop test, no other zone can be put into the test. The maintenance test will take five
minutes. During this time you can walk through the device and make sure all the devices are working properly. The
following table lists the status of the devices while in loop test.
You can cancel the maintenance test either by pressing the “RESET” key or by going into the configuration section
and canceling the test.
Note: Refer to How to Use the Keypad to Program the FA-300 on page 39 for detailed instructions on
making menu selections.
Note: Out of sensitivity can mean the device is dirty.
i
3
Detector Condition
Green LED Red LED
Proper operation Double blink every 5 sec OFF
Out of sensitivity OFF Double blink every 5 sec
Freeze condition OFF Double blink every10 sec
Perform the i3
Loop test? Y
-I3 TEST ZONES-
[ ]Zone-1
The selected zone
is not ready yet
The selected zone
is not i3 type
- FA-300 Series 1
- Copyrights and Trademarks 2
- Cautions and Warnings 3
- Contents 5
- List of Figures and Tables 7
- Industry Canada Notice 9
- Introduction 10
- Conventions 11
- System Components 12
- Relay Module: 12 Relays 13
- Relay Modules: Six Relays 13
- Polarity reversal/city tie 13
- Remote Annunciator 14
- Smart Relay Module 14
- Active end-of-line 15
- RAM-216 Remote Annunciator 15
- Mechanical Installation 16
- 3.5" 17
- 17" 18
- 22.5" 18
- Installing the Adder Modules 19
- BATTERY BATTERY 20
- Modules 21
- SYSTEM NORMAL 22
- 18:01 MON 2003-04-05 22
- BLK RED 23
- Connect to P6 on the 24
- + 26
- Field wiring 27
- FIRE ALARM MAIN BOARD 28
- 3.9K 1/2 WATT ELR 29
- Figure 18: Dialer wiring 30
- Relay Adder Module Wiring 31
- Power supply connection 32
- Battery Battery 33
- Auxiliary Power (unregulated) 34
- System Checkout 35
- Common Indicators 37
- Common Controls 37
- Common Relays 38
- Circuit Types 39
- Evacuation codes 40
- Figure 24: Evacuation Codes 40
- Fire Alarm Operation 41
- Supported Protocols/Devices 42
- Out of Sens Trb 1/ 1 43
- Freeze Trb. 1/ 1 43
- Configuration 44
- Command Menu 45
- Aux Dis Corr 47
- [X] DISABLE 47
- Aux Dis,Dis Alm&Spv 48
- Active EOL 49
- Zone-1 Type 50
- [X] ALARM 50
- Zone-12 Type 50
- NAC-1 Type 51
- [X] SIL-ABLE 51
- NAC-4 Type 51
- Zone-1 Label 52
- Zone-12 Label 52
- Load the default 53
- 2. Config Info (Command-Menu) 54
- 3. Set Time (Command-Menu) 55
- EAST LOBBY ENTRANCE 56
- OPEN TRB 01/09 56
- VERIFIED ALARM Z-01 56
- 2002/10/22 11:45.AM 56
- -Select Log 57
- 1 Alarm Log 57
- 2 General Log 57
- 3 All Logs 57
- 7. Walk Test (Command-Menu) 58
- Loop Test (Command-Menu) 59
- Account#1 ID: 60
- AuxDis Alm&Supv Rpt 63
- AC-Loss Delay(Hrs) 64
- Cellular Report Date 64
- -Ring Detect Number 65
- 1.L#1 Manual test 65
- 2.L#2 Manual test 65
- 14. Exit (Command-Menu) 68
- "INFO " Key 69
- City Tie trouble 72
- Active 1/ 1 72
- Trb:0x03 Info:0x0001 72
- 00:07 SAT 2000-01-01 72
- Appendix B: Reporting 74
- Appendix C: Specifications 76
- (Selection Guide) 77
- Limited Warranty 80
- Warranty Procedure 80
- Disclaimer of Warranties 80
- Out of Warranty Repairs 81
- © Mircom 2006 84
- Printed in Canada 84
Produits connexes et manuels pour Détecteurs de fumée Mircom FA-300 Series
(92 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.308 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels